CrossCanada: a biking documentary

posted by Caleb Kraft
filed under: daily, digital cameras hacks, wearable hacks

[Mike] was going to be biking across Canada. He really wanted to document the trip, so he began planning ways to get still images taken at intervals along the way. After a bit of brainstorming, he ended up setting his goals a bit higher. He was going to film the entire trip. He really didn’t want a simple helmet cam, he wanted himself and the entire bike in the frame. To do this he had to build a long arm on which he mounted a bullet cam. On his handlebars, he has a simple control where he can turn the system on and off as well as initiate recording.

No single piece of this project was too complicated, but taken all together, the final result is quite nice. You can watch the video for yourself after the break.

Read more...

Stereo microphones in an MSI Wind

[Matt] wrote in to tell us about this project. He plans on travelling with his MSI Wind and wanted better audio recording capabilities. He decided to install an additional microphone and a preamp. He made a custom preamp and wired it directly to the motherboard. The microphone was then mounted in the laptop screen. The second microphone is placed opposite of the first, about 18cm apart which [Matt] claims gives it a binaural effect. We think that this might just classify as stereo though. Wouldn’t you have to seperate them with a barrier or dampening device for binaural? It doesn’t really matter though, stereo mics are a great addition to the MSI Wind, and he did it very well. He does point out that it picks up a lot of noise though. There’s always room for improvement.

Read more...

Solar charging your DS

[dark sponge] decided to make his DS lite, solar powered. Or, at least charged via solar panels. He was able to find solar cells that were 60×60 mm, which means he could fit 4 of them on the outside of the DS. This gives him a total of 6V at 80 mA output. These panels charge the battery between uses. The DS has to be open and laying on its face for all 4 panels to be exposed, but this way of mounting them didn’t alter the pocket-ability of the unit. He says he’s been using it for a while and hasn’t had to plug it in yet, but we have concerns about wiring the panels directly to the battery. As [cyrozap] points out in the comments on the instructable, this is a Lithium Ion battery, shouldn’t there be some charging circuitry involved?

Read more...

NES controller on a DS

You can get most of the old NES games for the DS, but they just don’t feel the same. Sure your hands still cramp up, but its just not the same cramp we remember. What is the solution? Put an old Nintendo Entertainment System controller on your DS. [Parker] did exactly that. The method he used is fairly strait forward. He opened the DS, wired extensions onto the buttons he wanted to use to a controller. Instead of making it permanent though, he chose to wire it through the GBA slot. This allows him to plug the controller in whenever he wants to use it. This reminds us of the PSP with a SNES controller we covered back in October.

You can see a video of it in action after the break. You’ll notice in the video, he has also modded his buttons to have LEDs behind them.

In the comments, [tri-edge] points out that you can follow his build in the acidmods forum. There seem to be some other variations as well, including an SNES controller.

Read more...

Making the PSP not so portable

[alien x] has posted this peculiar hack for a PSP. He has gutted and splayed the PSP spreading its insides neatly and mounting them on a plexiglass back. Everything is easily accessible and ready to tinker with. It may not fit in your pocket, but adding mods and experimenting with ideas should be much easier like this. It looks pretty cool too, we want one for our office wall. That could be possible too, he’s selling it.

Read more...

Guitar Hero cymbal remake

[Matt] found, like many people, his Guitar Hero: World Tour cymbals left much to be desired. They were only detecting hits intermittently and starting to crack and fall apart as well. While he was waiting for his warranty replacements to arrive, he just couldn’t help by try to make his own improved version. Using about $25 worth of parts, mainly consisting of plastic plates and some neoprene material, he managed to make some pretty fantastic replacements. A video of them working might be a nice addition, but the writeup was pretty detailed otherwise.

Read more...

Augmented FPS gaming

[MikeFez] sent in this info about his augmented FPS set ups. He started this project back with an original XBox in 2006. He wanted a more immersive way of interacting with his games. Pointing out that gaming visuals and interactivity have come leaps and bounds while the controllers themselves have basically just added a few buttons, he explains his goals. He wanted to have to move his body to move his character and possibly physically aim. The original project, for the XBox, was successful in that he used a floor pad to control his character. Since then, the Wii has come out and he has moved to the PC as his main platform. As expected, he is now using the Wiimote as the aiming device.

Read more...